Skip to content

EMC#

Don't call EMC expert during the night if run is not physics

[QC on FLP - plot integrated over the run] Error Type for SM (Super Module)#

Green: good quality Red: bad quality
ErrorTypeOK ErrorTypeError
  • If no entries, a green message "No Error: OK" inform you that everything is working properly.
  • In case of errors, a red message will appear: call EMCAL oncall if EMCAL is included in global runs. Take note of the error-type in the y axis.

[QC on FLP] Payload Size/events#

good quality bad quality empty
PayloadSizeEvOK PLEvError PLEvempty
  • If "Data OK" is shown, everything is fine.
  • If some of the DDL presents entries that are larger than the others, a red message will appears: please call EMCAL oncall.
  • If the plot is empty, and EMCAL is included in the data taking, call EMCAL oncall.

[QC on FLP - plot integrated over the run] Bunch minimum amplitude EMCAL+DCAL#

good quality bad quality
BunchOK BunchError
  • One peak should be visibile for all supermodules around 0 if EMCAL is in data taking.
  • If the peak moves to the range 20-50 "Min raw amplitude (ADC)" for any supermodule, or a second peak appears for any supermodule in that range , call EMCAL oncall
  • If the plot is empty, and EMCAL is included in the data taking: please call EMCAL oncall

[QC on EPN - plot integrated over the run] Cell Occupancy plots (PHYS) for E>0.2 GeV and E<0.2 GeV and Cell Occupancy plots (CALIB) for E>0.5 GeV#

good quality bad quality (superMod not sending data) bad quaity (superMod noisy)
OccEbelowGOOD OccEbelow OccErr

Cell Occ. with E>0.2 GeV: the occupancy plots should be uniformly filled during Cosmics runs.
- if something noisy appears, please call the EMCAL oncall. - If the plot is empty, and EMCAL is included in the data taking, call EMCAL oncall.

Cell Occupancy plots with E>0.5 GeV (CAL)
- if some large empty areas (expect for the PHOS hole, present in the example for Cell Occ. with E<0.2 GeV) appear, please call EMCAL oncall.

[QC on EPN - plot integrated over the run] Cell Amplitude#

DigitAmplitude

  • no instructions for the moment.
  • If the plot is empty, and EMCAL is included in the data taking, call EMCAL oncall.
  • If peaks appear but the text in histogram is okay, That's a problem due to bad channel. send a message to EMCAL expert via mattermost.

[QC on EPN - plot integrated over the run] Cell Time#

DigitTime

  • If the plot is empty, and EMCAL is included in the data taking, call EMCAL oncall. If the errors appear during nigh shift:
  • add a note in the logbook, don't call the on-call.
  • in case LHC is preparing for collisions the on-call should be notified at "Prepare Ramp" (even during the night in this case) in case of such errors occur in a technical run before, so that the cards can be recovered before taking physics data.

Number of triggers per Time Frame#

good quality bad quality
DigitTimeOK DigitTime
Trigger rate appox. const with minor fluctuations Trigger rate dropping by several events / timeframe or to almost 0

The number of physics triggers per Time Frame must stay constant while the run is ongoing. In case the number of trigger decreases call the EMCAL on-call (for technical and cosmics runs not during the night). The correct value will depend on the interaction rate and a checker will be implemented soon; for the moment please inform the oncall on case of changes during the run.

Known issues#

  • Do not call EMC oncall during the night for QC plots related errors for non PHYSICS runs, unless a PHYSICS run is expected next.

  • For the plot "Number of Physics triggers per timeframe" the expected value is currently approx 20. If value is below 15 for at least 2 consecutive timestamps, call on-call.

  • Payload Size/Event can be ignored in all runs till further notice

  • In plot "Raw data errors" (error rate) quality is bad if the rate is above 100 errors / minute for several minutes, and good if it is below.

  • An empty region is expected near the bottom-right corner for CAL (Calibration) triggers. Cell Occupancy EMCAL,DCAL with E>0.5 GeV/c CAL